Menu

Your Complete Guide to LP® FlameBlock® Flame-Resistant Assemblies

Meeting code is just one of the many versatile benefits of LP® FlameBlock® Fire-Rated Sheathing. Combining structural capacity and design flexibility, LP FlameBlock assemblies are evaluated to help meet code requirements for fire-resistance construction as a component of 1-hour and 2-hour wall assemblies and in roof deck applications. 

LP FlameBlock sheathing may allow fire-resistance-rated walls to be assembled faster than common alternatives, so LP FlameBlock installation may help reduce labor costs while providing exceptional strength, durability and consistency.

While you may be familiar with the “original 8” UL and Intertek evaluated assemblies, LP Building Solutions has been adding additional assemblies to fit nearly all types of construction projects. Today, design professionals and architects have more than 30 LP FlameBlock fire-resistance-rated wall assemblies available for their projects.    

Quick Q&A: LP FlameBlock Assemblies

Before we dive in, let’s answer a few common questions:

Which LP FlameBlock fire ratings or fire-resistant wall assemblies should be used?

Before choosing among LP FlameBlock fire-resistance-rated wall assemblies, there are other elements that drive consideration. Load bearing or non-load bearing, type of construction, and occupancy category will dictate fire-resistance requirements.

What is 1-sided LP FlameBlock**?**

LP’s proprietary non-combustible, fiberglass-reinforced Pyrotite® coating is added to one side of an OSB panel––which slows the effects of heat and flames.

When should one-hour over two-hour be selected? 

“This is dictated by code,” says Scott Johnson, Construction Service Manager at LP Building Solutions. “Architects turn to the International Building Code (IBS), Chapter 6, which establishes construction time, such as Type III or Type IV construction.”

LP FlameBlock Assembly Highlights

Here are a few highlights of 2-sided and 1-sided LP FlameBlock assemblies for LP FlameBlock installation: 

UL Design U349 assembly is configured for Type III exterior load-bearing walls. It is a 2-hour wall and is fire-rated from inside. May eliminate the need for exterior gypsum.

  • Only 2.3˝ brick is needed (not 3.4˝)

  • Evaluated for both wood and steel studs

  • Also available in a two-hour interior only assembly

UL Design V337 assembly is commonly used in Type III and V exterior load-bearing walls. It is a 2-hour wall and is fire-rated on both sides. Assemblies are also available with 2.3˝ brick and with stucco.

UL Design V340 assembly is configured for exterior load-bearing walls. It is a 1-hour wall and is fire-rated on both sides. UL Design may be used in these applications:

  • Single-family exterior walls along property line

  • Type V exterior walls with Fire-Rated Dampers (FSD) less than 10 feet

  • Type I, II and III non-bearing exterior walls with FSD less than 10 feet

  • Double 1-hour walls for townhouse construction

  • Back-to-back Type V fire walls to achieve 2-hour fire resistance in accordance with NFPA 221, Table 4.6

21-sts-0025-m1mp-blog-chart-85x15375

We have more solutions for increased fire-resistance performance. If your project has somewhat uncommon requirements, it’s important to know there are many more LP FlameBlock assemblies listed under both UL and Intertek. Call LP at 615-610-1540 or your LP building solutions expert.

Continue Reading

Business Solutions

4 min

Q&A: How Home Orientation Impacts Continuous Insulation

There’s a lot to consider when it comes to building an energy-efficient home for your clients and the many nuances that change with each build—including its orientation to the sun. We sat down with Neil Freidberg, Building Science Manager at LP, to unpack the impact of home orientation on continuous insulation needs. 

Continue Reading

Resiliency Solutions

5 min
HOW A RADIANT BARRIER CAN IMPROVE BURIED DUCT PERFORMANCE

One of the questions LP® Building Solutions gets from builders often is about burying ducts in attic insulation and whether combining radiant barrier sheathing with blown insulation over ductwork can benefit homeowners. As with most technical situations, the outcome depends on a nuanced approach. Let’s dig in and explore this question. 

Sustainability Solutions

8 min
How to Drive Effective Communication and Collaboration on the Jobsite

Every jobsite has a ton of moving parts, from product shipments, supplies, and schedules to subcontractors and homeowners. It’s no wonder that many project teams can struggle to maintain quality jobsite communication and collaboration throughout the building process. And when communication slips, construction companies inevitably deal with costly errors, inefficient workflows, delayed projects, or wasted time, leaving clients and the team frustrated.

Sustainability Solutions

6 min
Carbon Negative, Future Positive: LP® Structural Solutions Portfolio Releases Environmental Product Declarations

In an era where environmental responsibility is paramount, we are proud to announce a remarkable achievement: the LP® Structural Solutions portfolio has been officially designated as carbon negative. This milestone is a testament to our unwavering commitment to redefining construction materials for the better with a focus on sustainability, resiliency and groundbreaking advancements.