Menu
Business Advice6 min

Taping in Tricky Areas

No matter the product you’re installing, proper technique and a few useful hints help ensure the product performs well for years to come. As an integrated WRB system, LP WeatherLogic® Air & Water Barrier represents a premium solution for building professionals. The panels install like OSB, and when the joints are sealed with LP WeatherLogic Seam & Flashing Tape, the system helps seal against water intrusion to finish the job. 

Taping across the panels of a wide, flat side of the house is fast and easy. But even seasoned pros can get tripped up on the finishing process when encountering other areas of the build, such as eaves, corners and wall penetrations. Let’s take a look at the best flashing tape techniques to achieve a good seal. 

What Is Flashing Tape?

Flashing tape provides an additional safeguard against water and air intrusion when used as part of an integrated WRB system. LP WeatherLogic Seam & Flashing Tape is specifically designed to work with LP WeatherLogic panels to deliver consistent long-term protection. Certified to AAMA 711-13, the tape uses one of today’s highest quality adhesives and can withstand temperature cycling. 

LP WeatherLogic Seam & Flashing Tape rolls are included with the panels and come in 3-3/4-inch and 6-inch widths. The wider flashing tape can be used for window flashing and is preferable for taping inside and outside corners.

lp-weatherlogic_1903-rgb_box_tape_900x

What Is the Best Tape for a Water Barrier?

Finding the best tape for a water barrier can help prevent water and air infiltration for your build. Construction Instruction, an independent building science group, conducted side-by-side testing with LP WeatherLogic panels and commodity-grade water-resistive barrier (WRB) over standard OSB sheathing. 

A standard window was installed with LP WeatherLogic tape on the LP WeatherLogic panel side and window flashing tape on the standard WRB side. After simulating a 50-mph rainstorm for 15 minutes, the team found the commodity-grade housewrap allowed water to leak into the wall cavity while the side with LP WeatherLogic panels showed no signs of water intrusion. See the test in full here.

How to Use Flashing Tape

Ensuring a proper seal at any interface can be tricky, and those areas where walls and roofs intersect can be especially tough. Installing LP WeatherLogic tape correctly and making sure you have a good seal is critical. Always make sure you apply the tape using firm pressure with the squeegee to ensure proper adherence. Be sure to consult the complete LP WeatherLogic flashing tape installation instructions before beginning.

Flashing Tape Installation: Inside and Outside Corners

Taping inside corners can be tough, but with a bit of practice and these tips you’ll soon get the hang of it. 

  • 6-inch LP WeatherLogic Seam & Flashing Tape is recommended. 

  • Center tape in the corner. 

  • Use the included squeegee to tightly push and crease the center of the tape fully into the corner. 

  • Adhere tape to both sides of the corner.

  • Alternatively, two layers of 3-3/4-inch LP WeatherLogic tape can be used.

  • Apply the first layer of tape to one side of the corner, leaving 1 inch to adhere to the opposite side.

  • Use the squeegee to crease and tightly push the tape into the corner.

  • Apply a second layer of tape to the other side of the corner, leaving 1 inch of tape to adhere over the first tape on the opposite side. Use the squeegee to crease and tightly push the tape into the corner.

Here are instructions on the proper technique for taping outside corners: 

  • 6-inch LP WeatherLogic Seam & Flashing Tape is recommended. Center tape over the corner. Fully adhere half of the tape width to one side and then tightly wrap over the corner to adhere the tape to the adjacent side.

  • Alternatively, two layers of 3-3/4-inch LP WeatherLogic tape can be used.

  • Adhere the first layer of tape 2 inches to one side and fold over the corner.

  • Adhere the second layer of tape 2 inches to the opposite side and fold over the corner to overlap the first tape.

_k4a1323_rt2sk_dw_900x

Flashing Tape Installation: Wall Penetrations

You will likely encounter penetrations with either straight or curved sides. Here are the proper sealings for both of these common areas: 

  • Penetrations with flanges with straight sides: 

  • If used as an air barrier, apply LP WeatherLogic Seam & Flashing Tape across the bottom. Center tape on the edge of the flange and extend approximately 1 inch past both sides. Do NOT extend tape more than 1-1/4 inches past the side flanges to ensure sufficient surface area for overlapping tape (next step) to bond to the panel.

  • Apply the tape to both side flanges. Center tape on flanges and extend approximately 1 inch past the top flange and at least 1 inch past the bottom flange tape. Do NOT extend tape more than 1-1/4 inches above the top flange to ensure sufficient surface area for overlapping tape (next step) to bond to the panel. The tape can extend more than 1 inch below the bottom flange tape.

  • Apply the tape to the top flange. Center tape on the flange and extend at least 2 inches past both pieces of side flange tape.

  • For straight-sided shapes other than rectangular, repeat the step for each “side flange,” working from bottom to top of the penetration.

weatherlogic_vent-tape_4-rgb_900x
  • Penetrations without flanges (or with curved sides):

  • Option 1: Use an approved flashing boot over the penetration. Secure the boot in accordance with the boot manufacturer’s instructions and tape the boot to the panel with LP WeatherLogic Seam & Flashing Tape according to “Penetrations with Flanges” instructions.

  • Option 2: Use a flexible (“stretch”) adhesive-backed flashing tape approved to AAMA 711-13 (711-20 for the 2021 IBC or IRC), a liquid-applied flashing certified to AAMA 714-15 (or newer) or a flexible flashing evaluated to ICC-ES Acceptance Criteria for Flexible Flashing Materials (AC148). Install in accordance with the manufacturer’s instructions.

Flashing Tape Installation: Eaves and Wall-to-Roof Transitions

These unique applications require specific sealing techniques as well.  

  • Tape roof-wall seam as an “inside corner” and install flashing at roof-wall transition as required by code.

  • Apply the LP WeatherLogic Seam & Flashing Tape to seal the top of the flashing. The tape should extend at least 2 inches onto the panel face and cover all fasteners used to attach the flashing. If the fasteners are placed so that the standard 3-3/4-inch tape cannot cover and extend 2 inches onto the panel, use the 6-inch tape or shingle multiple rows of 3-3/4-inch tape so that a layer above overlaps the layer below and covers the fasteners.

Start here to learn more about why you should use a good flashing tape, and then head over to our installation page to learn more flashing tape installation techniques.

Continue Reading

Business Solutions

4 min

Q&A: How Home Orientation Impacts Continuous Insulation

There’s a lot to consider when it comes to building an energy-efficient home for your clients and the many nuances that change with each build—including its orientation to the sun. We sat down with Neil Freidberg, Building Science Manager at LP, to unpack the impact of home orientation on continuous insulation needs. 

Continue Reading

Resiliency Solutions

5 min
HOW A RADIANT BARRIER CAN IMPROVE BURIED DUCT PERFORMANCE

One of the questions LP® Building Solutions gets from builders often is about burying ducts in attic insulation and whether combining radiant barrier sheathing with blown insulation over ductwork can benefit homeowners. As with most technical situations, the outcome depends on a nuanced approach. Let’s dig in and explore this question. 

Sustainability Solutions

8 min
How to Drive Effective Communication and Collaboration on the Jobsite

Every jobsite has a ton of moving parts, from product shipments, supplies, and schedules to subcontractors and homeowners. It’s no wonder that many project teams can struggle to maintain quality jobsite communication and collaboration throughout the building process. And when communication slips, construction companies inevitably deal with costly errors, inefficient workflows, delayed projects, or wasted time, leaving clients and the team frustrated.

Sustainability Solutions

6 min
Carbon Negative, Future Positive: LP® Structural Solutions Portfolio Releases Environmental Product Declarations

In an era where environmental responsibility is paramount, we are proud to announce a remarkable achievement: the LP® Structural Solutions portfolio has been officially designated as carbon negative. This milestone is a testament to our unwavering commitment to redefining construction materials for the better with a focus on sustainability, resiliency and groundbreaking advancements.